Water Soluble Fertilizer Calculator

Fertilizer label
The three big numbers on a fertilizer bag are N, P₂O₅ and K₂O. Pick elemental only if your label lists % P and % K.
% N
% P₂O₅
% K₂O
% Ca
From the guaranteed analysis, e.g. 19% for calcium nitrate.
% Mg
Your requirements
ppm
In the irrigation water that reaches the plants, not in the stock tank.
Final volume of the tank (batch) or of the stock solution (injector). Dissolve the fertilizer, then top up to this mark.
Extras (optional)
Shows how much solution one whole bag makes.
g/mL
From the product's safety data sheet; usually 0.7–1.4 g/mL. Converts the weight to tablespoons.
Biology Updated 5 Nov 2026

Mix a liquid feed that hits an exact nutrient concentration. Enter the analysis from the fertilizer label (as N-P₂O₅-K₂O or as elemental N-P-K, plus calcium or magnesium if listed), choose the nutrient you are targeting and its concentration in ppm or mmol/L, and the calculator returns the grams or ounces of soluble fertilizer to dissolve, the ounces per 100 gallons, and the ppm and mmol/L of every other nutrient the recipe delivers. Switch to injector mode to size a concentrated stock tank for a 1:16, 1:100 or 1:200 proportioner, or check how many gallons of stock one bag will make.

  • Label percentages are the guaranteed analysis by weight; ppm means mg per litre of water (the solution density is taken as 1 kg/L).
  • Nutrients already present in the source water are not included; subtract them from the target if a water test shows significant Ca, Mg or nitrate.
  • The injector ratio is the volume of diluted feed per volume of stock; check the real ratio regularly by calibration or by measuring EC.
  • The calculator does not recommend a feeding rate for a crop – use grower guides or extension advice for that.

Formula

Target ppm = mmol/L × molar mass (if entered in mmol/L). Fertilizer in the feed (mg/L) = target ppm ÷ (nutrient % ÷ 100). Stock strength = feed strength × injector ratio. Fertilizer to weigh = strength × volume. Other nutrients (ppm) = feed strength × their %; P = P₂O₅ ÷ 2.2913, K = K₂O ÷ 1.2046.
  • ppm is mg of nutrient per litre of water. 200 ppm N from a 20% N fertilizer needs 200 ÷ 0.20 = 1,000 mg/L, i.e. 1 g of product per litre.
  • Extension shortcut: oz per US gallon of stock = ppm × ratio ÷ (% × 75), and g/L = ppm × ratio ÷ (% × 10). The 75 is rounded; the exact figure, 1 oz per 100 US gal = 74.89 mg/L, is used here, so results run about 0.15% above the rounded rule.
  • An injector with ratio 1:100 delivers 100 gallons of diluted feed per gallon of stock, so the stock must be 100 times stronger than the feed.
  • Bag numbers give phosphorus and potassium as oxides. Elemental P = P₂O₅ ÷ 2.2913 and K = K₂O ÷ 1.2046, from IUPAC atomic weights (P 30.974, K 39.098, O 15.999).
  • mmol/L converts to ppm by multiplying by the molar mass in g/mol: N 14.007, P 30.974, K 39.098, Ca 40.078, Mg 24.305.

200 ppm N in a 100-litre tank from 20-8-20

Inputs
  • How will you apply it?: batch
  • Label type: oxide
  • Nitrogen: 20 % N
  • Phosphorus: 8
  • Potassium: 20
  • Calcium (optional): % Ca
  • Magnesium (optional): % Mg
  • Nutrient you are targeting: n
  • Concentration unit: ppm
  • Target concentration: 200
  • Injector ratio 1 :: 100
  • Volume to mix: 100
  • Volume unit: L
  • Bag weight (optional):
  • Bag unit: lb
  • Bulk density (optional): g/mL

200 ppm N is 200 mg/L. The fertilizer is 20% N, so the water needs 200 ÷ 0.20 = 1,000 mg/L = 1.000 g/L of product, or 13.35 oz per 100 US gallons. For 100 L that is 1 × 100 = 100.00 g (3.53 oz). The same 1 g/L supplies 1,000 × 0.08 = 80.0 ppm P₂O₅ (34.9 ppm P) and 1,000 × 0.20 = 200.0 ppm K₂O (166.0 ppm K).

Sources & references

  • The Basics of Fertilizer Calculations for Greenhouse Crops (Publication 430-100)
    Virginia Cooperative Extension, Virginia Tech · Retrieved 5 Nov 2026

    Stock formula amount = ppm × dilution factor ÷ (% element × C), C = 75 for oz/US gal, 1,200 for lb/US gal, 10 for g/L; injector ratio definition; examples 20-10-20 at 200 ppm N with a 1:98 injector (13.1 oz/gal, 262 oz in 20 gal, 30.5 gal per 25 lb bag) and 13-0-44 for 200 ppm K at 1:100 (7.27 oz/gal, ~71 ppm N).

  • Calculators for Mixing Water-Soluble Fertilizer
    University of New Hampshire Extension · Retrieved 5 Nov 2026

    Same inputs for injector stock (ppm N, injector ratio 1:x, % N) and gallons of stock per whole bag; top up to the final stock volume rather than adding fertilizer to a full tank.

Frequently asked questions

How do I calculate ppm of nitrogen from a water-soluble fertilizer?
ppm N = grams of fertilizer per litre × % N × 10. One gram per litre of 20-10-20 gives 1 × 20 × 10 = 200 ppm N. In US units, ppm N ≈ ounces per 100 gallons × % N × 0.75, so 10 oz of 20-10-20 in 100 gallons gives about 150 ppm N.
How much fertilizer goes into the stock tank for a 1:100 injector?
Multiply the feed strength by 100. For 200 ppm N from 20-10-20 the feed needs 1 g/L, so the stock needs 100 g/L, which is about 13.35 oz per US gallon of stock. Dissolve the fertilizer in part of the water first, then top up to the final volume.
Why does my 20-20-20 not give 200 ppm of phosphorus when it gives 200 ppm N?
The middle and last numbers are P₂O₅ and K₂O, not P and K. At 1 g/L, 20-20-20 supplies 200 ppm P₂O₅ but only 200 ÷ 2.29 = 87.3 ppm P, and 200 ppm K₂O is 166.0 ppm K.
How do I convert mmol/L to ppm for a nutrient recipe?
Multiply by the molar mass of the element. 5.4 mmol/L of calcium is 5.4 × 40.078 = 216.4 ppm Ca; with calcium nitrate at 19% Ca, that needs 216.4 ÷ 0.19 = 1,139 mg/L, about 1.14 g per litre.
How many gallons of stock does a 25 lb bag make?
Divide the bag weight by the stock strength. For 200 ppm N from 20-10-20 through a 1:98 injector the stock is 98 g/L (13.09 oz per gallon), so 25 lb = 400 oz makes about 30.6 US gallons of stock.

Related calculators

Fertilizer Calculator Work out how much granular fertilizer to spread from the N-P-K grade on the bag. Enter the area of your lawn, garden or field, the three label numbers and the rate of nitrogen, phosphate (P₂O₅) or potash (K₂O) you want to apply, and the calculator returns the product rate per area, the total weight to spread, the other nutrients that come along with it and how many bags to buy. Switch to the product mode to see what a known spreading rate delivers. Works in m², ft², acres and hectares with kg or lb. CO₂ Grow Room Calculator Works out how much carbon dioxide to release into a grow room, grow tent or small greenhouse to lift it from the current concentration to a target level such as 1,200–1,500 ppm. Enter the room's width, length and height (or its volume) in metric or imperial units and the two CO₂ readings in ppm to get the gas volume in liters, cubic meters and cubic feet, plus its mass from the density of CO₂. Give the time the tank valve stays open to get the regulator flow rate, or give the flow rate to get the time. An optional air-change rate estimates the extra flow needed to hold the target against leakage, and the result flags targets above the 5,000 ppm workplace exposure limit. Molarity Calculator Calculates the molarity of a solution, or works backwards to the mass of solute or the volume of solution you need for a target molarity. Molarity is the amount of dissolved substance in moles per litre of solution (mol/L, written M). Enter the molar mass with the mass of solute and the final volume, a target molarity, or a mass concentration in g/L, and get the molarity, moles of solute and concentration.