Tree Leaves Calculator
Estimates how many leaves are on a tree with a paper plate and a tape measure. Cover a round plate with one layer of the tree's leaves and count them, measure how wide the crown's shadow is on the ground, then pick the species: its leaf area index (LAI) says how many layers of leaves sit above each patch of ground. The result is an order-of-magnitude estimate, not a count. Optional sections turn the figure into the number of lawn bags and the weight of leaves to rake from your yard, and estimate how many leaves are in a cone-shaped pile.
- This is a rough estimate of the order of magnitude, not a leaf count.
- The crown's ground projection is treated as a circle, and leaves on the plate as one gap-free, non-overlapping layer.
- Species LAI values are averages for full summer foliage; trees in autumn, drought or after pruning carry fewer leaves.
- Leaf piles are modelled as cones and full bags hold leaves at the same density as a squashed hand-made ball.
Formula
- The plate count gives how many leaves cover a unit of ground in a single layer. Multiplying by the crown's ground area gives the leaves needed to shade that ground once.
- Leaf area index (LAI) is the one-sided leaf area above each square metre of ground, so it is the average number of leaf layers in the crown. For flat broadleaves the area of a leaf lying on a plate is its one-sided (projected) area, the same basis the LAI values use.
- Species LAI presets are typical values: 4.7 for a typical deciduous tree, from 2.73 (quaking aspen) to 6.64 (sugar maple). They sit close to the global mean of about 4.5 found in a review of over 1,000 field measurements (Asner and others, 2003), but the single-species figures are not taken from a published table. Real trees vary a lot with site, age and season, so treat the answer as an order of magnitude.
- Because only the ratio of areas matters, the plate and crown units cancel: in the worked example 9 × (360 in ÷ 10 in)² × 4.7 = 54,821 leaves.
- Bags and piles use a leaf 'packing density': leaves in a hand-made ball ÷ the ball's volume. A squashed ball imitates leaves pressed into a bag; a loose ball imitates a pile, which is treated as a cone.
- Bag weight = bag volume × packing density × mass of one leaf; total mass = trees × leaves × mass of one leaf.
Sycamore maple in a yard
- Units: imperial
- Leaves on one tree: estimate
- Plate diameter: 10
- Number of leaves on the plate: 9
- Tree crown projection diameter: 30
- Tree species: typical
- Leaf area index (LAI): 4.7
- Number of leaves on a tree: 100000
- Number of trees: 1
- Squashed ball diameter: 6
- Number of leaves in the squashed ball: 40
- Bag volume: 39
- Average mass of one leaf: 0.5
- Loose ball diameter: 8
- Number of leaves in the ball: 30
- Pile diameter: 6
- Pile height: 4
Nine leaves cover a 10 in plate and the crown's shadow is 30 ft (360 in) across, so one layer over the crown area takes 9 × (360 ÷ 10)² = 11,664 leaves. With the typical deciduous LAI of 4.7 the tree carries about 4.7 × 11,664 = 54,821 leaves, or about 50 thousand. A squashed 6 in ball holds 40 leaves, so a 39-gallon bag holds about 3,186 leaves and the tree fills 17.21 bags (have 18 ready). At 0.5 dr per leaf that is 107.07 lb of leaves, about 6.22 lb per bag. A loose 8 in ball of 30 leaves means a 6 ft wide, 4 ft high cone-shaped pile holds 7,290 leaves.
Sources & references
- A Global Database of Field-observed Leaf Area Index in Woody Plant Species, 1932-2011 (Iio, A. and Ito, A., 2014), dataset documentation
- Global synthesis of leaf area index observations: implications for ecological and remote sensing studies (Asner, Scurlock and Hicke, Global Ecology and Biogeography 12: 191–205, 2003)