Daily Light Integral (DLI) Calculator
Converts a grow light or sunlight reading into the daily light integral, the total number of photosynthetically active photons a square meter of canopy receives in one day. Enter the photosynthetic photon flux density (PPFD) from a quantum sensor in µmol/m²/s and how long the light is on, in hours, minutes or seconds, to get the DLI in mol/m²/day. Switch the mode to work backwards: find the PPFD a fixture must deliver to hit a target DLI, or how many hours a light must run to reach it.
- PPFD is the average photosynthetic photon flux (400–700 nm) at plant height and stays constant while the light is on.
- Lux and foot-candle readings are not accepted because they weight light for the human eye; their conversion to PPFD depends on the light source.
Formula
DLI = PPFD × light hours × 3,600 ÷ 1,000,000; PPFD = DLI × 1,000,000 ÷ (hours × 3,600); hours = DLI × 1,000,000 ÷ (PPFD × 3,600)
- DLI is in mol/m²/day, PPFD in µmol/m²/s and the photoperiod in hours. 3,600 converts hours to seconds and 1,000,000 converts µmol to mol, so DLI = PPFD × hours × 0.0036.
- Minutes and seconds are converted to hours first (÷ 60 or ÷ 3,600). The photoperiod cannot exceed 24 hours.
- The formula assumes the PPFD is constant while the light is on. Sunlight changes through the day, so for outdoor or greenhouse light use the average PPFD over the photoperiod, or a logging sensor that sums the readings.
- The 24-hour equivalent PPFD is DLI ÷ 0.0864 (86,400 seconds per day ÷ 1,000,000): the steady light that would give the same DLI if it never switched off.
- Results are rounded to 2 decimal places; the photon total is rounded to a whole µmol.
1,500 µmol/m²/s for 9 hours
Inputs
- Calculate: dli
- Light hours per day: 9 h
- Time unit: h
- Photon flux density (PPFD): 1500 µmol/m²/s
- Target daily light integral (DLI): 48.6 mol/m²/day
DLI = 1,500 × 9 × 3,600 ÷ 1,000,000 = 48,600,000 ÷ 1,000,000 = 48.60 mol/m²/day. The light is on for 9 ÷ 24 = 37.50% of the day, and spreading the same 48.6 mol evenly over 24 hours would need 48.6 ÷ 0.0864 = 562.50 µmol/m²/s.
Sources & references
Frequently asked questions
How do I calculate DLI from PPFD?
Multiply the PPFD in µmol/m²/s by the hours the light is on and by 3,600, then divide by 1,000,000. A lamp giving 100 µmol/m²/s for 12 hours supplies 100 × 3,600 × 12 ÷ 1,000,000 = 4.32 mol/m²/day.
How much DLI do plants need?
Cornell University's rules of thumb are 8–12 mol/m²/day for rooted cuttings and plugs, 10–12 or more for bedding plants, 15–17 for hydroponic lettuce and 20–30 or more for tomatoes. Seedlings are often started around 6–8 mol/m²/day.
What PPFD do I need for a given DLI?
Divide the DLI by 0.0036 × the photoperiod in hours. To give lettuce 17 mol/m²/day over 16 hours you need 17 ÷ (0.0036 × 16) = 295.14 µmol/m²/s at canopy height.
How much DLI does the sun provide?
A sunny summer day can deliver around 65 mol/m²/day outdoors, with about 2,000 µmol/m²/s at noon, while a cloudy winter day may give only about 1 mol/m²/day. A greenhouse typically transmits 50–70% of the outdoor light.
Is PPF the same as PPFD?
No. PPF (µmol/s) is the total photosynthetic photon output of a lamp, while PPFD (µmol/m²/s) is how many of those photons land on each square meter of the plant surface. DLI is calculated from PPFD.
Related calculators
Water Potential Calculator Adds up the components of water potential (Ψ = Ψs + Ψp + Ψg, plus hydrostatic, overburden and matric terms for soils) to show which way water will move. Solute potential can be typed in or worked out from the solute concentration with Ψs = −iCRT, using the ionization constant, molarity and temperature in °C or K. You can also solve backwards for the pressure (turgor) potential or for the solute potential and the concentration that would produce it, in bar, MPa, kPa, atm, psi or hPa. Corn Yield Calculator Estimates corn grain yield before harvest with the yield component method used by Purdue, Iowa State and the University of Illinois. Count the harvestable ears in a 1/1000-acre length of row, enter the kernels per ear (or kernel rows and kernels per row) and pick a kernel size of 120,000, 90,000 or 80,000 kernels per 56-lb bushel, or type your own. You get bushels per acre, tonnes per hectare, the total crop for your field in bushels and tonnes, and the gross value and profit at your corn price. A row-spacing helper tells you how long the 1/1000-acre sample row has to be.