Log Reduction Calculator

Colony counts
Colony forming units in the untreated (control) sample.
Colony forming units surviving the treatment. Enter 0 if no colonies grew.
Biology Updated 29 Oct 2026

Measure how well a disinfectant, sanitizer, heat step or filter kills microbes. Enter the colony forming units (CFU) before and after treatment, each with its own power-of-ten multiplier, to get the log reduction and percent reduction. You can also convert between log and percent reduction, or work out the surviving CFU (or the starting load) needed for a target 3-log, 5-log or 6-log kill.

  • The initial count comes from an untreated control that represents the load before treatment.
  • Both counts are corrected for dilution and expressed on the same basis (per mL, per carrier, etc.).
  • Log reduction uses base-10 logarithms.

Formula

Log reduction = log₁₀(initial CFU ÷ final CFU). Percentage reduction = (initial CFU − final CFU) ÷ initial CFU × 100 = (1 − 10^(−log reduction)) × 100. Final CFU = initial CFU × 10^(−log reduction)
  • Each CFU field is the entered number times its power-of-ten multiplier, so 5 with × 10⁷ means 50,000,000 CFU.
  • Log reduction is rounded to 4 decimal places. The percentage keeps enough decimals to show the surviving share to three significant figures, so 5 log is shown as 99.999% rather than rounded up to 100%.
  • Reverse solving: initial CFU = final CFU × 10^(log reduction); from a percentage, initial CFU = final CFU ÷ (1 − percentage ÷ 100).
  • If no colonies grow (final CFU = 0) the reduction is 100% and the log reduction can only be given as a lower bound, log₁₀(initial CFU).

Disinfectant test: 5 × 10⁷ CFU reduced to 2 × 10⁵ CFU

Inputs
  • Calculate: counts
  • Reduction is given as: log
  • Initial CFU (before treatment): 5
  • Multiplier: 7
  • Final CFU (after treatment): 2
  • Multiplier: 5
  • Log reduction: 3
  • Percentage reduction: 99.9 %

The ratio is 50,000,000 ÷ 200,000 = 250, so the log reduction is log₁₀ 250 ≈ 2.3979. The percentage reduction is (50,000,000 − 200,000) ÷ 50,000,000 = 99.6%: one microbe in 250 survived the treatment.

Sources & references

Frequently asked questions

How do I convert log reduction to percent?
Percent reduction = (1 − 10^(−LR)) × 100. Each whole log adds a 9: 1 log = 90%, 2 log = 99%, 3 log = 99.9%, 4 log = 99.99%, 5 log = 99.999% and 6 log = 99.9999%. Going the other way, LR = −log₁₀(1 − percent ÷ 100).
What log reduction is considered good?
It depends on the purpose and the governing standard. Hand sanitizer and surface tests commonly look for 3 to 5 log, food-contact sanitizers are often expected to reach 5 log (99.999%), and sterilization processes are designed around much larger theoretical reductions such as a 12-log reduction of resistant spores. Always check the specific test method or regulation that applies.
Why use log reduction instead of percent?
Microbial counts span many orders of magnitude, and percentages crowd together near 100%: 99.9% and 99.999% look almost the same but differ by a factor of 100 in survivors. Log reduction turns each tenfold drop into one unit, so treatments are easier to compare.
What if no colonies grow after treatment?
A count of zero means the survivors fell below the detection limit, not that the log reduction is infinite. Report it as 'greater than or equal to' log₁₀(initial CFU ÷ detection limit). The calculator shows this lower bound assuming one CFU could have been detected; adjust for your plating volume and dilution if needed.
Do the initial and final counts need the same units?
Yes. Use CFU per mL, per carrier or per plate consistently for both, after correcting each for its own dilution factor. The multiplier selects let you enter numbers such as 3.2 × 10⁶ without typing all the zeros.

Related calculators