One Rep Max (1RM) Calculator

Lift-specific NSCA coefficients cover 1–10 repetitions.
kg
reps
Whole reps done with good form before failure. Estimates are most reliable at 2–10 reps.
Health Updated 5 Nov 2026

Estimates your one-repetition maximum (1RM) from a weight you lifted for several reps to failure. With no lift selected it uses the Epley equation, w × (1 + reps/30); for the squat, deadlift or bench press it uses the NSCA rep coefficients for 1–10 reps. It then turns your 1RM into a percentage-of-max loading chart, a 1–15 rep-max chart and training-goal loads, and compares seven published prediction equations (Brzycki, Lander, Lombardi, Mayhew, O'Conner, Wathan, Epley) in kilograms or pounds.

  • This is an estimate, not a measured maximum; real 1RMs commonly differ from predictions by 5–10% or more.
  • Reps are counted to failure with consistent technique and full range of motion.
  • Warm up properly and use a spotter or safety bars for any heavy set or 1RM attempt.
  • Not medical advice: people with injuries, heart conditions or other health concerns should check with a doctor or qualified coach before maximal lifting.

Formula

1RM = w × (1 + r/30) (Epley, no lift selected); 1RM = w × NSCA coefficient for r reps (squat, deadlift, bench press)
  • w is the weight lifted and r the number of repetitions completed to failure. With exactly 1 rep the weight itself is reported as the 1RM.
  • NSCA coefficients for 2–10 reps: squat 1.0475–1.41, deadlift 1.065–1.24, bench press 1.035–1.325 (for example 5 reps: squat 1.2, deadlift 1.164, bench 1.15). These lift-specific coefficients are widely attributed to the NSCA, but the NSCA's own training load chart uses one column for all lifts, and the original publication of the lift-specific table could not be traced.
  • Comparison equations (LeSuer et al. 1997): Brzycki w × 36/(37 − r); Lander 100w/(101.3 − 2.67123r); Lombardi w × r^0.10; Mayhew 100w/(52.2 + 41.9e^(−0.055r)); O'Conner w(1 + 0.025r); Wathan 100w/(48.8 + 53.8e^(−0.075r)).
  • The rep-max chart rounds Brzycki's (37 − r)/36 for 1–10 reps (5 reps: 89%) and Epley's 1/(1 + r/30) for 11–15 reps (15 reps: 67%). The NSCA training load chart gives slightly lower values, for example 87% for 5 reps and 70% for 12 reps.
  • Goal loads (95, 90, 80, 70 and 50% of 1RM) are the calculator's guide values. ACSM's 2009 position stand gives ranges: strength with eventual emphasis on heavy 1–6 RM loads, hypertrophy mainly 6–12 RM, power through strength training plus light loads of 0–60% (lower body) or 30–60% (upper body) moved fast, and muscular endurance 40–60% for more than 15 reps. The 70% endurance value is heavier than the ACSM range.
  • Loads are 1RM × percentage. The 1RM is shown to 2 decimals and chart loads to 1 decimal; 1 lb = 0.45359237 kg exactly.
  • Above 10 reps the equations diverge sharply, so treat those estimates as rough.

100 kg for 5 reps, lift not specified

Inputs
  • Lift: none
  • Unit: kg
  • Weight lifted: 100 kg
  • Repetitions completed: 5 reps

Epley: 1RM = 100 × (1 + 5/30) = 100 × 1.1667 = 116.67 kg (257.21 lb). Hypertrophy work at 80% uses 116.67 × 0.80 = 93.3 kg and strength work at 95% uses 110.8 kg. If the lift was a squat, the NSCA 5-rep coefficient gives 100 × 1.2 = 120.00 kg; for a bench press 100 × 1.15 = 115.00 kg; Brzycki gives 100 × 36/32 = 112.50 kg.

Sources & references

Frequently asked questions

How do I calculate my one rep max?
Warm up, then lift a weight you can manage for about 2–10 reps with good form until you cannot complete another rep. Multiply the weight by (1 + reps/30) for the Epley estimate: 100 kg for 5 reps gives about 116.7 kg.
Which 1RM formula is most accurate?
None is best for everyone. In LeSuer and colleagues' 1997 test of seven equations on 67 untrained students, predictions correlated highly with real 1RMs (r > 0.95), yet only two equations were unbiased for the bench press, one for the squat and none for the deadlift, which all of them underestimated. The formulas agree closely at low reps and drift apart as reps rise.
How many reps should I use to estimate my 1RM?
A set of about 2–6 reps gives the most reliable estimate, and up to 10 is acceptable. With more reps, muscular endurance plays a bigger part and the equations can differ from your true maximum by 10% or more.
What percentage of my 1RM should I train with?
The calculator uses these guide values: about 95% of 1RM for maximal strength, 90% for power, 80% for muscle growth (hypertrophy), 70% for muscular endurance and 50% for fast, explosive work. Published ranges are wider: the American College of Sports Medicine suggests heavy 1–6 RM loads for strength, mainly 6–12 RM for hypertrophy, light loads of up to 60% of 1RM moved fast for power, and 40–60% with more than 15 reps for muscular endurance. The rep-max chart shows the load you can typically lift for 1–15 reps.

Related calculators